3IN1 MIG Welder 200A Gas/Gasless ARC Stick MMA Lift-TIG Inverter Welder 110/220v

Description

[Sango Ichi Multifunctional Welder]
MIG 255 offers ARC welding mode, TIG welding, and MIG welding mode, and really realizes welding function 3 go 1. It has a 2 T / 4 T mode switching function and is suitable for spot welding and long welding. Has overcurrent protection, overpressure protection, and overheat protection. The machine has a built-in wire plate axle. No plug, 1 kg / 5 kg 0.8-1.0 mm wire plate is applied. The plug is a three-hole plug.
[Gas-free welding]
Gas & gasless -1kg / 5kg 0.8-1.0mm (0.03 "-0.039") Solid wire (iron for gas welding); 0.8-1.0mm Flux-filled wire (without gas welding) Carbon steel and stainless steel. In normal gas welding mode, the polarity can be changed to weld the drug core. Realizes gas welding that does not really use gas. (When using the DC tangential method, the ground clamp is connected to the positive electrode and a polarity switch is required, that is, the wire connecting rod is connected to the negative electrode.
[MIG welding]
Output current range: MIG 25-200A; MIG 255 centralized adjustment can automatically achieve current-voltage matching. Even beginners can easily adjust welding parameters. Welders can perform higher quality welds on plates of different thicknesses with fine-tuning voltage and arc characteristics.
[TIG welding]
Output current range: TIG 10-200A Suitable for welding thin plates of φ0.8 mm to φ1.2 mm or more. The automatic delay control of TIG welding gas removes the arc punch and the initial forming of the bead is beautiful.
[We guarantee for one year and present consumables. ]
As a responsible company, we guarantee quality for one year.
MIG255-3 in 1 MIG welding machine
MIG 255 offers ARC welding mode, TIG welding, MIG welding mode, and really realizes welding function 3 go 1.
It has a 2 T / 4 T mode switching function and is suitable for spot welding and long welding. Has overcurrent protection, overpressure protection, and overheat protection.
The machine has a built-in wire plate axle. A 1 kg / 5 kg 0.8-1.0 mm wire plate is applied.
Please note: Because this machine is sold in many countries, it is not equipped with a power plug. You only need to buy a plug that meets local standards and install it.
Gasless welding
Gas & Gasless-1kg / 5kg 0.8-1.0mm (0.03 "-0.039") Solid Wire (Iron for Gas Welding); 0.8-1.0mm Fluxed Wire (No Gas Welding) Carbon Steel and Stainless Steel
MIG welding
Even beginners can easily adjust welding parameters. Welders can perform higher quality welds on plates of different thicknesses with fine-tuning voltage and arc characteristics.
TIG welding
Output current range: TIG 10-200A Suitable for welding thin plates of φ0.8 mm to φ1.2 mm or more.
MMA welding
It has a good arc and a constant output during welding, which has the optimum effect on both the forming of the weld bead and the inherent quality.
Welding example
This is an example of good welding with uniform pace and penetration.
1 x TIG torch
1 x MIG torch
1 x welding holder
1 x ground clamp
Ready to work
Reference opinion at the time of beginner welding
Weld the surface clean and make sure it is free of paint, rust, greasy, dirt and other materials.
Very convenient to clean and prepare. For example, use a grinding machine, a wire brush, or compressed air.
If you want to use clean exposed metal. Also, be careful not to use chemical solvents to prepare and clean unless it is determined that it will not be decomposed into harmful gases.
Many solvents, such as brake cleaners, are widely used for surface cleaning during car repairs. However, there are still a small amount of chemicals left inside that contain some detergents. These trace chemicals can then be further decomposed during the welding process into extremely harmful gases.
The machine uses much heavier connectors and leads for the MIG, TIG, and MMA welding torches. The machine is capable of higher power and better welds because of the improved amperage your leads carry.
The machine's arc is smoother, start more powerfully, and does not cause much splatter even with flux core.
For beginners
For beginners, this machine is a good choice. Easy to operate and control, it can be used with the wire or gas of the drug core. In the long run, good equipment can save you time and money.
Parameter information
Input voltage
220V±15%
Input current
27.6-32 A
Output voltage
15-28 V DC
Output current range
TIG:10-200 A ;MMA:10-200A ;
MIG:25-200 A
Pulse frequency
50/60 Hz